JOB ID:162317
Job Type
Returnee Program
Functional Area
Software Development
Industry
Electrical/Electronics/Semiconductor
Education
Not Specified
Experience Required
5 - 12 Yrs
Key Skills Required
ssd hardware project, pcb design, emi/esd protection, cadence, allegro, sigrity, allegro power-aware si, mentor graphics hyperlynxOther Skills Required
Duties and Responsibilities
• Document and communicate results with cross functional counterparts.
• Interface in cross functional teams to ensure the design meets all firmware, diagnostic and system level requirements.
• Participate in architecture definition, design reviews, requirements generation of SSD products.
• Design and Architect SSD platforms with custom SSD Controllers, NAND and DRAM for cost sensitive SSD products.
• Design and Architect power systems targeted for cost sensitive SSD products.
• Simulate and analyze design proposals, review results and provide recommendations on optimal design practices to other design engineers.
• Design with schematic capture and design constraints utilizing Cadence PCB design tools.
• Run simulations of all power systems utilizing SPICE simulation tools and models.
• Evaluation of Worst-case analysis, simulations and de-rating.
• Design with understanding of signal integrity behavior of high-speed interfaces.
• PCB back-end pr
... See MoreDuties and Responsibilities
• Document and communicate results with cross functional counterparts.
• Interface in cross functional teams to ensure the design meets all firmware, diagnostic and system level requirements.
• Participate in architecture definition, design reviews, requirements generation of SSD products.
• Design and Architect SSD platforms with custom SSD Controllers, NAND and DRAM for cost sensitive SSD products.
• Design and Architect power systems targeted for cost sensitive SSD products.
• Simulate and analyze design proposals, review results and provide recommendations on optimal design practices to other design engineers.
• Design with schematic capture and design constraints utilizing Cadence PCB design tools.
• Run simulations of all power systems utilizing SPICE simulation tools and models.
• Evaluation of Worst-case analysis, simulations and de-rating.
• Design with understanding of signal integrity behavior of high-speed interfaces.
• PCB back-end process: defining stack-up and via technologies, part placement, setting design constraints, signal integrity and power integrity analysis
• Experienced in designing hardware for large scale manufacture, including DFx and low-cost considerations
• Define test plans for verification of Power Management ICs and power systems.
• Define test equipment and procedures required to complete hardware verification of SSD and focused Power Management IC testing.
• Perform basic Signal and power integrity measurements
• Perform hands on power system and power integrity testing using procedures and test equipment.
• Perform margin-based testing with focus on Voltage / Temp / Process and test to fail conditions.
• Perform temperature-based testing within chambers and developing scripts and automation to improve efficiency.
• Interface with cross functional teams to ensure the PMIC and PCB design meets all requirements. (Diagnostic Firmware, system level, procurement supply chain and manufacturing).
• Works proactively with cross functional team members during design, verification as well as on RMAs
• In addition to design, a successful Engineer will mentor and provide technical guidance to other hardware team members
• Successful Engineer will modify existing and develop new test procedures to improve test coverage
Critical Skills
• Self-motivated. Desire to take on challenges. Result-driven and details oriented.
• Able to lead an SSD Hardware project with a team to completion.
• Strong interpersonal and communication skills are a must.
• Strong analog experience at the board level for power system design.
• Strong in transmission line fundamentals. Understand the fundamentals of time-domain vs. frequency-domain.
• Strong In-depth knowledge in circuit designs, as well as semiconductor design.
• Strong PCB design experience on high speed signals routing guideline and review, power copper routing and review, design for EMI/ESD protection.
• Design for signal integrity, including SerDes, power and interconnect.
• Develops solutions to complex technical problems, which require ingenuity and creativity.
• Strong analog design using simulation e.g. SPICE (or equivalent).
• Strong practical experience with design tools: Cadence, Allegro, Sigrity, Allegro Power-Aware SI, Mentor Graphics HyperLynx
• Practical lab SI analysis experience using: High-bandwidth measurements (20-35GHz)
• PCIe Compliance equipment
• Strong understanding of how P/V/T and proper margining are used for design verification.
• Experience with script (e.g. Python) development for automated testing of SSD or equivalent hardware
• Practical Lab experience with using soldering station and microscope.
Qualification Requirements
• BS in Electrical Engineering required; MS in Electrical Engineering is preferred
• 10+ years of relevant design experience
• Excellent written and verbal communication
• Excellent problem solving skills See Less